pulley problem

Go here for posts about rebuilds, parts and problems
Post Reply
mercury mitch
Member
Posts: 626
Joined: Mon Mar 29, 2010 8:49 pm
Location: Paradise Tasmania

pulley problem

Post by mercury mitch »

Bought 2 new pullies for 350 chev when fitted they hit each other , they are the same brand but cheap china,brand new water pump .Dont know if pump shaft position varies at all,any help or sugestions.Be nice now :D :D :D
Life is a learning curve, endevour to learn something new every day jees I hope I never get alz alz alz alz
User avatar
steve the ford guy
Senior Member
Posts: 1576
Joined: Mon Apr 19, 2010 9:36 pm

Re: pulley problem

Post by steve the ford guy »

http://www.superchevy.com/how-to/49718- ... s-brackets
The pumps vary in length even when stock, shims can be added this page explains more about it. I'm no expert but hope this helps you Mitch :D
Last edited by steve the ford guy on Wed Jun 03, 2020 11:17 pm, edited 1 time in total.
Greg N Smith
Senior Member
Posts: 1070
Joined: Thu Jan 05, 2006 1:47 am
Location: Sunshine Coast QLD

Re: pulley problem

Post by Greg N Smith »

I'm thinking Mercury Mitch's problem is that the diameter of one or both pulleys (crank and waterpump) is too large - not a belt alignment issue ?

Can you post a photo of the pulleys fitted if possible and let us know the pulley diameters ?

Then I will check my 283 and let you know
User avatar
pilot Dave
Old Hand
Posts: 2657
Joined: Wed Nov 23, 2005 9:17 am
Location: tassie land of no footy
Contact:

Re: pulley problem

Post by pilot Dave »

Mitch I had same trouble with new ones I bought I think the brand was RPC or rpm something like that they are too thin to machine down ...ask me how I know I tossed them in the rubbish I bought 2 more nof different brand it was about 5yrs ago so memorys a bit thin like pulleys were
https://www.youtube.com/watch?v=Z1-DNj8eSf0
User avatar
FRANK BASILE
Old Hand
Posts: 13895
Joined: Wed May 07, 2003 3:14 pm

Re: pulley problem

Post by FRANK BASILE »

Had similar issue some months back when setting the 350 that came in with the 49 pick up for aircon and power steering . I tried using crank pulleys and water pump pulleys and power steer pump from my spare 350 . Aside to the long/short water pump issue, I did find different diameter pulleys. Water pump pulley from memory. All good now I had to buy in a dual p/s pump pulley from the US.though.
OZ-E-Rodders Rod and Kustom Club Member #31
User avatar
32V8
Posts: 353
Joined: Thu Jul 15, 2004 9:59 am
Location: Perth. W.A.

Re: pulley problem

Post by 32V8 »

mercury mitch wrote:but cheap china,brand new water pump
Theres your problem.
mercury mitch
Member
Posts: 626
Joined: Mon Mar 29, 2010 8:49 pm
Location: Paradise Tasmania

Re: pulley problem

Post by mercury mitch »

Image
Water pump pulley is same size as other motor, im thinking maybe issue with water pump
Life is a learning curve, endevour to learn something new every day jees I hope I never get alz alz alz alz
User avatar
pilot Dave
Old Hand
Posts: 2657
Joined: Wed Nov 23, 2005 9:17 am
Location: tassie land of no footy
Contact:

Re: pulley problem

Post by pilot Dave »

they look like the pulleys I had got rid of them std chev ones went straight on was nothing to do with my water pump Mitch
I tried them on my crate spare motor as well same thing if it was pump it would mean the shaft is too low
my pulleys came on an orange card from memory and RPC or rpm was brand name

this is ones I got

https://www.ebay.com.au/itm/S9600-CHEV- ... SwPNBdCJUd
https://www.youtube.com/watch?v=Z1-DNj8eSf0
User avatar
Sudsy
Senior Member
Posts: 1576
Joined: Sat Apr 08, 2006 2:59 pm
Location: Lower Mid North South Australia

Re: pulley problem

Post by Sudsy »

Must be all the chrome they put on them that's makes them bigger :D :D :D :D :D
Regards Bob
Post Reply