351 Clevo Engine mounts custom

Go here for posts about rebuilds, parts and problems
Post Reply
User avatar
hugh ness
Member
Posts: 875
Joined: Tue Mar 08, 2011 7:51 pm

351 Clevo Engine mounts custom

Post by hugh ness »

Hey guys and girls.
Currently have a 351c mated to some really funky mounts off the Jag front end.
A couple of guys have seen the engine mounted like this and have said it fits okay so leave it.
BUT...
I think it sits too high and think it needs to come further back to the firewall and dropped down about two inches.
That way the c4 auto doesn't smack into the cabin floor (In fact if I keep this arrangement will have to modify the cab floor)
as well its a little more in line with the diff etc.
I saw this kit online and wondered what you guys thought of it?
FORD 289, 302, 351W into 1953-64 FORD Pickup- Motor Mount Kit
here is a pic of it sitting in the engine bay.

Notice I have the Bronco rear sump arrangement to clear the front end.
Should I just leave the damned thing alone as it doesn't foul anything where it is, or should I mess with stuff and put it where I think it
wants to live?
I think it should clear the firewall okay once I put the goody bits on it.
You do not have the required permissions to view the files attached to this post.
Twin Spinner
Senior Member
Posts: 1470
Joined: Mon Jan 02, 2012 7:45 pm
Location: Brisbane.

Re: 351 Clevo Engine mounts custom

Post by Twin Spinner »

You may have firewall clearance problems with exhaust manifolds/extractors, I fitted a cleavo in a 57 F100 many years ago and had to drop the engine a little, pretty sure there was a starter motor/steering box clearance problem as well??? :? :)
If it has tits or wheels, you can expect trouble.
User avatar
hugh ness
Member
Posts: 875
Joined: Tue Mar 08, 2011 7:51 pm

Re: 351 Clevo Engine mounts custom

Post by hugh ness »

Yes, good points. Hadn't given the steering intermediate shaft much thought.
Might have to stick a Chevy in there after all. Ha ha!
Twin Spinner
Senior Member
Posts: 1470
Joined: Mon Jan 02, 2012 7:45 pm
Location: Brisbane.

Re: 351 Clevo Engine mounts custom

Post by Twin Spinner »

A much better motor, OOOPS :oops: :lol: Just hope Monte don't see this :D
If it has tits or wheels, you can expect trouble.
User avatar
zuffen
Old Hand
Posts: 2014
Joined: Fri Jan 28, 2011 7:45 pm
Location: Sydney

Re: 351 Clevo Engine mounts custom

Post by zuffen »

If you feel it's not in the right place, move it.

Every time you open the bonnet it will annoy you.

It isn't hard to move it just keep in mind the things that may interfere with the engine.

Moving it down and back would certainly get the nose heavy, understeer a bit more under control.
Never argue with an idiot, they will drag you down to their level and beat you with experience.
User avatar
Sudsy
Senior Member
Posts: 1582
Joined: Sat Apr 08, 2006 2:59 pm
Location: Lower Mid North South Australia

Re: 351 Clevo Engine mounts custom

Post by Sudsy »

I would move it down and back as far as you can then fabricate new mounts to suit
Regards Bob
User avatar
46 deluxe
Old Hand
Posts: 3656
Joined: Sun Aug 17, 2003 12:50 am
Location: geelong vic

Re: 351 Clevo Engine mounts custom

Post by 46 deluxe »

Oil pan will be your biggest problem with a clevo .
But it looks like you have a bronco pan under it so that may help a bit .
i can tell you a good old y block will work with a jag front . :wink:
scott
User avatar
Newbee
Member
Posts: 594
Joined: Mon May 26, 2014 10:59 pm
Location: YP of SA

Re: 351 Clevo Engine mounts custom

Post by Newbee »

Here are some photos of my setup Jag FE in the 52 Mainline 5 L Windsor with later style hydraulic engine mounts, mine sits low on
the cross member and tight with the trans tunnel, I may have to lift it to get more engine angle.

IMG_0831.jpg
IMG_0846.jpg
IMG_0849.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
Newbee
Member
Posts: 594
Joined: Mon May 26, 2014 10:59 pm
Location: YP of SA

Re: 351 Clevo Engine mounts custom

Post by Newbee »

Tight fit but OK
IMG_0863.jpg

Steering shaft clears OK

IMG_0864.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
hugh ness
Member
Posts: 875
Joined: Tue Mar 08, 2011 7:51 pm

Re: 351 Clevo Engine mounts custom

Post by hugh ness »

Thanks for your responses guys. You're right about me not being happy where it is. I'll measure it up.
User avatar
hugh ness
Member
Posts: 875
Joined: Tue Mar 08, 2011 7:51 pm

Re: 351 Clevo Engine mounts custom

Post by hugh ness »

Was looking at this style of engine mount. Looked neat but did seem flimsy. Spoke with engineer and he said he wasn't that impressed. I then showed him the Tuff Mounts option and he said they seem much better.
images_ePIM_original_4101-mount_w960_h600_q80.jpg
tuff.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
zuffen
Old Hand
Posts: 2014
Joined: Fri Jan 28, 2011 7:45 pm
Location: Sydney

Re: 351 Clevo Engine mounts custom

Post by zuffen »

The first lot do look flimsy. The old 351 isn't exactly light.

I'd follow the Engineers opinion.
Never argue with an idiot, they will drag you down to their level and beat you with experience.
User avatar
turns
Old Hand
Posts: 2925
Joined: Mon Dec 17, 2007 8:23 pm
Location: Sydney NSW

Re: 351 Clevo Engine mounts custom

Post by turns »

The top kit doesn't lend itself to solving your problem in my opinion. I agree they look flimsy and the chassis mount will be in single shear at best. Both of the kits will be 'less cushioned' than the factory mount you currently have. Certifiers typically like OEM parts over aftermarket.

Try and get your engine mocked up exactly where you need it to be. Use the whole engine assembly with heads and consider all factors such as manifolds, exhaust, steering, cooling system etc. I assume that you have plenty of real estate in the F100 to play with and try to think of all components that have to fit.

Lots of good suggestions from members so far

Cheers Turns
"Normal is an illusion. What is normal for the spider is chaos for the fly"...............Morticia Addams
enjenjo
Senior Member
Posts: 1050
Joined: Sun Jun 23, 2002 10:45 am
Location: swanton ohio
Contact:

Re: 351 Clevo Engine mounts custom

Post by enjenjo »

The bottom kit doesn't look to bad but I would add some gussets to the frame half of the mount, and maybe box the top of the same part.
People who think they know it all, bother those of us that do.
Retro Boy
Senior Member
Posts: 1325
Joined: Fri Aug 04, 2006 10:22 am
Location: Freeling SA
Contact:

Re: 351 Clevo Engine mounts custom

Post by Retro Boy »

Cut your engine mounts down. Chuck away the top brackets and make some flat brackets up in place of them. Easy as.
You do not have the required permissions to view the files attached to this post.
https://www.facebook.com/OldRaceCarsHotRodsInSheds
Post Reply