Finally gettin a start on the rod(rollin n channelled)
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
-
- Old Hand
- Posts: 3249
- Joined: Sun Dec 12, 2010 8:36 am
- Location: Gosford, NSW
Re: Finally gettin a start on the rod(rollin n channelled)
Nice !!
Is the sticker from the movie "they live?" (obey)
Cheers, Mudgy
Is the sticker from the movie "they live?" (obey)
Cheers, Mudgy
Good Judgement comes from experience....experience comes from bad judgement.
- Chrisso
- Old Hand
- Posts: 4178
- Joined: Thu Apr 12, 2012 10:44 am
- Location: Albury NSW
Re: Finally gettin a start on the rod(rollin n channelled)
Nice progress Gerry, looks as though things are moving along very cool.
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
Re: Finally gettin a start on the rod(rollin n channelled)
Not sure have seen it round a bit, a mate gave it to meMudgy wrote:Nice !!
Is the sticker from the movie "they live?" (obey)
Cheers, Mudgy
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
Re: Finally gettin a start on the rod(rollin n channelled)
Yeah been a bit done since the photobucket scandalChrisso wrote:Nice progress Gerry, looks as though things are moving along very cool.
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Finally gettin a start on the rod(rollin n channelled)
Great to see another old farrier in the mix here as did the same 30 years ago! Still got my anvil as you may have noticed and should mount it too as beats using it on your knees on the floor!
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
Re: Finally gettin a start on the rod(rollin n channelled)
Yeah, not good for the knees mate, old rim bit of plate and box section and ur done, don't forget the heavy rope to take the RIIIIING out of itGojeep wrote:Great to see another old farrier in the mix here as did the same 30 years ago! Still got my anvil as you may have noticed and should mount it too as beats using it on your knees on the floor!
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
Re: Finally gettin a start on the rod(rollin n channelled)
WTF???????? where have all my pics gone this time??
Can you guys see them?
Can you guys see them?
-
- Old Hand
- Posts: 3249
- Joined: Sun Dec 12, 2010 8:36 am
- Location: Gosford, NSW
Re: Finally gettin a start on the rod(rollin n channelled)
I see them, this page and the last. Didn't go back further. If you have dramas, I'll check mate.
Cheers, Mudgy
Cheers, Mudgy
Good Judgement comes from experience....experience comes from bad judgement.
- Newbee
- Member
- Posts: 578
- Joined: Mon May 26, 2014 10:59 pm
- Location: YP of SA
Re: Finally gettin a start on the rod(rollin n channelled)
Just read your whole thread there Coop great work, your getting there, perseverence will pay off in the end.
Pics all look OK for me.
Just getting a start on my chassis, long way to go !
Regards Newbee
Pics all look OK for me.
Just getting a start on my chassis, long way to go !
Regards Newbee
- Chrisso
- Old Hand
- Posts: 4178
- Joined: Thu Apr 12, 2012 10:44 am
- Location: Albury NSW
Re: Finally gettin a start on the rod(rollin n channelled)
All good here Gerry, you haven't had a tipple have you???
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
Re: Finally gettin a start on the rod(rollin n channelled)
Must be a pooter setting as all i see is a logo and the word image
Any help appreciated
Any help appreciated
- 46 deluxe
- Old Hand
- Posts: 3643
- Joined: Sun Aug 17, 2003 12:50 am
- Location: geelong vic
Re: Finally gettin a start on the rod(rollin n channelled)
What are you using as a web browser ?302-coop wrote:Must be a pooter setting as all i see is a logo and the word image
Any help appreciated
Older versions of explorer can cause issues .
scott
- 302-coop
- Member
- Posts: 971
- Joined: Thu Jan 01, 2009 11:13 pm
- Location: Mt Gambier SA
Re: Finally gettin a start on the rod(rollin n channelled)
Hey there, using Chrome46 deluxe wrote:What are you using as a web browser ?302-coop wrote:Must be a pooter setting as all i see is a logo and the word image
Any help appreciated
Older versions of explorer can cause issues .